Polyester Capacitors Filmite® “E”, ORANGE DROP®, Radial Lead
PERFORMANCE CHARACTERISTICS
Operating Temperature: - 55°C to + 85 °C To + 105 °C when working voltage is reduced to 70 % of
+ 85 °C rating; to + 125 °C when working voltage is reduced to 50 % of 85 °C rating
Insulation Resistance: After a 2 minute charge at rated
voltage or 500 V, whichever is less. At + 25 °C: 100 000 Megohm for C ≤ 0.25 Microfarads 25000 Megohm - Microfarads for C > 0.25 Microfarads At + 85 °C: 10 000 Megohm for C ≤ 0.15 Microfarads 1500 Megohm - Microfarads for C > 0.15 Microfarads At + 105 °C: 1500 Megohm for C ≤ 0.17 Microfarads 250 Megohm - Microfarads for C > 0.17 Microfarads At + 125 °C: 200 Megohm for C ≤ 0.13 Microfarads 25 Megohm - Microfarads for C > 0.13 Microfarads
Capacitance Tolerance and Dissipation Factor:
Capacitors shall be measured at a frequency of 1000 Hz at
FEATURES
-
Utilizes minimum area where printed wiring board space is most important
-
Wound from PETP polyester film and thin gauge
RoHS
foil under carefully controlled atmospheric
conditions
-
Protected against moisture by a conformal coating of epoxy
-
Specifically designed for printed wiring board applications
-
Widely used in computers, instrumentation and telecommunications equipment
-
100 VDC through 600 VDC, may be operated up to
+ 125 °C with proper dearting
Dielectric Withstanding Voltage:
Capacitors shall withstand a DC potential of 250 % of rated voltage applied between terminals for not more than 5 seconds. The test voltage must be applied and discharged through a resistor of 1 ohm per volt.
Humidity Test:
Condition capacitors with no voltage applied for 72 hours at 95 % relative humidity and + 75 °C. Remove capacitors from humidity chamber, wipe surface dry of moisture and dry in circulating air for 4 hours. Measure insulation resistance after a 2 minute charge at 25 °C and rated voltage or 500 VDC, whichever is less. Minimum product of insulation resistance and capacitance shall be 5000 Megohm - Microfarads after test but need not exceed 10 000 Megohm. Not more than one failure allowed in 12 units tested.
DC Life Test:
Capacitance are capable of withstanding a 500 hour life test at + 85 °C at 150 % of rated working voltage. After test, capacitance shall not have changed by more than 5 % of initial value, insulation resistance shall not have decreased by more than 50 % of the initial limit and dissipation factor shall not have increased to more than 1 %.
-
+
-
25 °C or else be referred to measurements made at that frequency and temperature. The maximum dissipation factor shall be 0.75 %
|
DIMENSIONS in inches [millimeters] |
|
|
|
Terminal A L Max. 0.237 [6.020] Max. S ± 0.060 [1.524] Lead Length " Terminal B 0.237 [6.020] Max. L Max. S ± 0.030 [0.762] Lead Length |
Terminal D L Max. S ± 0.030 [0.762] H Max. Lead Length |
0.237 [6.020] Max. T Max. Tinned Copper-Clad Steel 0.032 [0.813] Dia. (No. 20 AWG) |
|
CASE CODE |
L (Max.) |
|
S |
|
Terminal A and B |
|
Terminal D |
|
W |
0.70 [17.78] |
0.562 [14.275] |
|
0.375 [9.525] |
|
X |
0.80 [20.32] |
0.613 [15.570] |
|
0.375 [9.525] |
|
Y |
1.25 [31.75] |
0.969 [24.613] |
|
0.719 [18.263] |
Type 225P
Vishay Sprague Polyester Capacitors Filmite® “E”, ORANGE DROP®, Radial Lead
|
DISSIPATION FACTOR VS.TEMPERATURE |
|
TYPICAL - 55 - 40 - 25 0 + 25 + 50 + 75 + 85 + 105 + 125 - 50 + 100 TEMPERATURE DEG. CENTIGRADE 1.5 1.0 0.5 0 % DISSIPATION/1000 Hz |
|
STANDARD RATINGS* |
|
|
|
|
µF ± 10 % TOLERANCE PART NUMBER |
L |
SIZE H |
T |
|
100 VDC/70 VAC** |
|
|
|
0.001 225P10291W 0.0012 225P12291W 0.0015 225P15291W 0.0018 225P18291W 0.0022 225P22291W 0.0027 225P27291W 0.0033 225P33291W 0.0039 225P39291W 0.0047 225P47291W 0.0056 225P56291W 0.0068 225P68291W 0.0082 225P82291W 0.01 225P10391W 0.012 225P12391W 0.015 225P15391W 0.018 225P18391W 0.022 225P22391W 0.027 225P27391W 0.033 225P33391W 0.039 225P39391W 0.047 225P47391W 0.056 225P56391W 0.068 225P68391W 0.082 225P82391W 0.1 225P10491W 0.12 225P12491X 0.15 225P15491X 0.18 225P18491X 0.22 225P22491X 0.27 225P27491X 0.33 225P33491X 0.39 225P39491X 0.47 225P47491X 0.56 225P56491Y 0.68 225P68491Y 0.82 225P82491Y 1.0 225P10591Y |
0.70 [17.78] 0.70 [17.78] 0.70 [17.78] 0.70 [17.78] 0.70 [17.78] 0.70 [17.78] 0.70 [17.78] 0.70 [17.78] 0.70 [17.78] 0.70 [17.78] 0.70 [17.78] 0.70 [17.78] 0.70 [17.78] 0.70 [17.78] 0.70 [17.78] 0.70 [17.78] 0.70 [17.78] 0.70 [17.78] 0.70 [17.78] 0.70 [17.78] 0.70 [17.78] 0.70 [17.78] 0.70 [17.78] 0.70 [17.78] 0.70 [17.78] 0.80 [20.32] 0.80 [20.32] 0.80 [20.32] 0.80 [20.32] 0.80 [20.32] 0.80 [20.32] 0.80 [20.32] 0.80 [20.32] 1.25 [31.75] 1.25 [31.75] 1.25 [31.75] 1.25 [31.75] |
0.35 [8.89] 0.35 [8.89] 0.35 [8.89] 0.35 [8.89] 0.35 [8.89] 0.35 [8.89] 0.35 [8.89] 0.35 [8.89] 0.35 [8.89] 0.35 [8.89] 0.35 [8.89] 0.35 [8.89] 0.35 [8.89] 0.35 [8.89] 0.35 [8.89] 0.35 [8.89] 0.35 [8.89] 0.37 [9.40] 0.37 [9.40] 0.42 [10.67] 0.42 [10.67] 0.49 [12.45] 0.49 [12.45] 0.55 [13.97] 0.55 [13.97] 0.57 [14.48] 0.62 [15.75] 0.66 [16.76] 0.70 [17.78] 0.74 [18.80] 0.77 [19.56] 0.81 [20.57] 0.86 [21.84] 0.88 [22.35] 0.90 [22.86] 0.94 [23.88] 0.98 [24.89] |
0.25 [6.35] 0.25 [6.35] 0.25 [6.35] 0.25 [6.35] 0.25 [6.35] 0.25 [6.35] 0.25 [6.35] 0.25 [6.35] 0.25 [6.35] 0.25 [6.35] 0.25 [6.35] 0.25 [6.35] 0.25 [6.35] 0.25 [6.35] 0.25 [6.35] 0.25 [6.35] 0.25 [6.35] 0.27 [6.86] 0.27 [6.86] 0.30 [7.62] 0.30 [7.62] 0.34 [8.64] 0.34 [8.64] 0.40 [10.16] 0.40 [10.16] 0.37 [9.40] 0.40 [10.16] 0.43 [10.92] 0.46 [11.68] 0.49 [12.45] 0.52 [13.21] 0.55 [13.97] 0.60 [15.24] 0.55 [13.97] 0.58 [14.73] 0.65 [16.51] 0.72 [18.29] |
* Parts ordered with D3 leads are standard capacitors in stock and available through the Sprague® Distribution Network. For complete Part
Number, add letter and number for terminal and lead length. See Ordering Information (Ex: 225P39391WD3). **60 Hz rms
Type 225P
Polyester Capacitors Vishay Sprague Filmite® “E”, ORANGE DROP®, Radial Lead
|
STANDARD RATINGS* in inches [millimeters] |
|
|
|
µF ± 10 % TOLERANCE PART NUMBER L |
SIZE H |
T |
|
200 VDC/140 VAC** |
|
|
|
0.001 225P10292X 0.80 [20.32] 0.0015 225P15292X 0.80 [20.32] 0.0022 225P22292X 0.80 [20.32] 0.0033 225P33292X 0.80 [20.32] 0.0047 225P47292X 0.80 [20.32] 0.0068 225P68292X 0.80 [20.32] 0.01 225P10392X 0.80 [20.32] 0.015 225P15392X 0.80 [20.32] 0.022 225P22392X 0.80 [20.32] 0.033 225P33392X 0.80 [20.32] 0.047 225P47392X 0.80 [20.32] 0.068 225P68392X 0.80 [20.32] 0.1 225P10492X 0.80 [20.32] 0.1 225P10492Y 1.25 [31.75] 0.15 225P15492X 0.80 [20.32] 0.22 225P22492X 0.80 [20.32] 0.33 225P33492Y 1.25 [31.75] 0.47 225P47492Y 1.25 [31.75] 0.68 225P68492Y 1.25 [31.75] |
0.55 [13.97] 0.55 [13.97] 0.55 [13.97] 0.55 [13.97] 0.55 [13.97] 0.58 [14.73] 0.58 [14.73] 0.58 [14.73] 0.58 [14.73] 0.61 [15.49] 0.61 [15.49] 0.64 [16.26] 0.71 [18.03] 0.64 [16.26] 0.74 [18.80] 0.77 [19.56] 0.71 [18.03] 0.83 [21.08] 1.14 [28.96] |
0.25 [6.35] 0.25 [6.35] 0.25 [6.35] 0.25 [6.35] 0.25 [6.35] 0.25 [6.35] 0.25 [6.35] 0.25 [6.35] 0.25 [6.35] 0.28 [7.11] 0.28 [7.11] 0.31 [7.87] 0.37 [9.40] 0.31 [7.87] 0.41 [10.41] 0.48 [12.19] 0.41 [10.41] 0.50 [12.70] 0.84 [21.34] |
|
400 VDC/200 VAC** |
|
|
|
0.001 225P10294X 0.80 [20.32] 0.0015 225P15294X 0.80 [20.32] 0.0022 225P22294X 0.80 [20.32] 0.0033 225P33294X 0.80 [20.32] 0.0047 225P47294X 0.80 [20.32] 0.0068 225P68294X 0.80 [20.32] 0.01 225P10394X 0.80 [20.32] 0.015 225P15394X 0.80 [20.32] 0.022 225P22394X 0.80 [20.32] 0.033 225P33394X 0.80 [20.32] 0.047 225P47394X 0.80 [20.32] 0.047 225P47394Y 1.25 [31.75] 0.068 225P68394X 0.80 [20.32] 0.1 225P10494X 0.80 [20.32] 0.1 225P10494Y 1.25 [31.75] 0.15 225P15494Y 1.25 [31.75] 0.22 225P22494Y 1.25 [31.75] 0.33 225P33494Y 1.25 [31.75] 0.47 225P47494Y 1.25 [31.75] |
0.55 [13.97] 0.55 [13.97] 0.55 [13.97] 0.55 [13.97] 0.55 [13.97] 0.58 [14.73] 0.58 [14.73] 0.58 [14.73] 0.58 [14.73] 0.65 [16.51] 0.65 [16.51] 0.64 [16.26] 0.80 [20.32] 0.84 [21.34] 0.74 [18.80] 0.80 [20.32] 0.89 [22.61] 0.99 [25.15] 1.14 [28.96] |
0.25 [6.35] 0.25 [6.35] 0.25 [6.35] 0.25 [6.35] 0.25 [6.35] 0.25 [6.35] 0.28 [7.11] 0.28 [7.11] 0.31 [7.87] 0.34 [8.64] 0.41 [10.41] 0.31 [7.87] 0.47 [11.94] 0.52 [13.21] 0.41 [10.41] 0.47 [11.94] 0.56 [14. 22] 0.72 [18.29] 0.84 [21.34] |
* Parts ordered with D3 leads are standard capacitors in stock and available through the Sprague® Distribution Network. For complete Part
Number, add letter and number for terminal and lead length. See How to Order (Ex: 225P39391WD3). ** 60 Hz rms
Type 225P
Vishay Sprague Polyester Capacitors Filmite® “E”, ORANGE DROP®, Radial Lead
-
*
-
60 Hz rms
|
STANDARD RATINGS* in inches [millimeters] |
|
|
|
µF ± 10 % TOLERANCE PART NUMBER L |
SIZE H |
T |
|
600 VDC/200 VAC** |
|
|
|
0.001 225P10296X 0.80 [20.32] 0.0015 225P15296X 0.80 [20.32] 0.0022 225P22296X 0.80 [20.32] 0.0033 225P33296X 0.80 [20.32] 0.0047 225P47296X 0.80 [20.32] 0.0068 225P68296X 0.80 [20.32] 0.01 225P10396X 0.80 [20.32] 0.015 225P15396X 0.80 [20.32] 0.018 225P18396X 0.80 [20.32] 0.022 225P22396X 0.80 [20.32] 0.033 225P33396X 0.80 [20.32] 0.039 225P39396X 0.80 [20.32] 0.047 225P47396X 0.80 [20.32] 0.068 225P68396Y 1.25 [31.75] 0.1 225P10496Y 1.25 [31.75] 0.22 225P22496Y 1.25 [31.75] |
0.55 [13.97] 0.55 [13.97] 0.55 [13.97] 0.55 [13.97] 0.58 [14.73] 0.58 [14.73] 0.64 [16.26] 0.67 [17.02] 0.74 [18.80] 0.74 [18.80] 0.77 [19.56] 0.83 [21.08] 0.83 [21.08] 0.82 [20.83] 0.91 [23.11] 1.10 [27.94] |
0.25 [6.35] 0.25 [6.35] 0.25 [6.35] 0.25 [6.35] 0.25 [6.35] 0.25 [6.35] 0.31 [7.87] 0.34 [8.64] 0.37 [9.40] 0.37 [9.40] 0.44 [11.18] 0.50 [12.70] 0.50 [12.70] 0.47 [11.94] 0.56 [14.22] 0.76 [19.30] |
* Parts ordered with D3 leads are standard capacitors in stock and available through the Sprague® Distribution Network. For complete Part Number, add letter and number for terminal and lead length. See How to Order (Ex: 225P39391WD3).
Note: Some Part Numbers are in stock and available through the Vishay Sprague® Distribution Network. Other Part Numbers are available on special order through Vishay Sprague® Distribution. In the construction of the components described, the full intent of the specification will be met. Vishay however, reserves the right to make, from time to time, such departures from the detail specifications as may be required to permit improvements in the design of its products. The information included herein is believed to be accurate and reliable. However, Vishay Sprague® assumes no responsibility for its use nor for any infringements of patens of other rights of third parties which may result from its use.
Disclaimer
All product specifications and data are subject to change without notice.
Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, “Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained herein or in any other disclosure relating to any product.
Vishay disclaims any and all liability arising out of the use or application of any product described herein or of any information provided herein to the maximum extent permitted by law. The product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase, including but not limited to the warranty expressed therein, which apply to these products.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay.
The products shown herein are not designed for use in medical, life-saving, or life-sustaining applications unless otherwise expressly indicated. Customers using or selling Vishay products not expressly indicated for use in such applications do so entirely at their own risk and agree to fully indemnify Vishay for any damages arising or resulting from such use or sale. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications.
Product names and markings noted herein may be trademarks of their respective owners.
